|-- Board Configuration the press can be configured as a board press to accept web stock of 12 to 24 point board stock. The press is manufactured with larger diameter idler rollers.
|-- 70" roll diameter unwind module with 12" diameter air cores and roll adjustment. This module also includes a web tension control system and a pneumatic lift.
|-- Dual web package adds an additional unwind and web guide to bring two webs into the press at the same time.
|-- Automatic Registration Control System this electronic system will adjust and maintain the registration of the print stations automatically to allow hands free operation of the press.
|-- Reverse Angle Doctor Blade this is a quick release design to allow for quick change over.
|-- Enclosed Doctor Blade System is a cartridge system which eliminates the need for the meter roll and ink pan.
|-- Strobe light or Video Web Inspection Unit are devices that allow the operator to monitor the printing quality on the web, while the press is running, before it is wound on the rewind core. The strobe light includes a manual control and all necessary connections and mounting brackets. The video web inspection unit includes a camera, a computer and a monitor unit.
|-- Turnover bar is a device that allows the web to be turned over between any two print stations. It lets you print on both sides of the web by turning the web over while running. It consists of two idler rollers, two air bars and an air regulator.
|Diaphragm or variable speed peristaltic ink pumps, which help regulate the ink additives outside of the ink pan. Ink pumps provide a constant flow of ink into the ink pan. They are especially useful for high volume printing facilities.
|-- Ink pan covers to prevent contamination of airborne debris, and reduce solvent evaporation.
|-- Reversible print heads to allow for backside printing without the use of a turnover bar.
|-- Helical gears replace the spur gears on the print stations helps minimizes gear marking.
|-- Second 24" roll diameter waste wind-up for dual winding of waste die cutting product. This unit consists of a small idler, an adjustable belt driven capstan and a take up roll.
|-- 24" roll diameter lamination arm is a device that allows you to add another layer of to the top of the web, usually a clear film. This unit includes an air actuated unwind tension control, a lateral adjust knob, a guide roll, ironing roll and pressure blocks and the Laminator Control Panel which includes the core “ON/OFF” switch, the brake “ON/OFF” switch and the brake tension gauge and regulator knob.
|-- Razor, air circular or mechanical circular slitter knife assembly with side-to-side adjustment. Slitters let you slit, score or perforate the web longitudinally while printing. The air circular type includes an Air Slitter Control Panel located at the Master Control Panel with an “ON/OFF” switch which operates the air valve that supplies air to activate the slitter blades and a “Pressure Regulator” that regulates the air pressure supplied to the slitter blades. The pressure setting is determined by the cutting requirements.
|-- Fixed or adjustable die adaptors (to make use of dies shorter than standard, which are driven from the backside of the press) include all die pressure adjusting units and necessary bearing blocks.
|-- Second 30” or 40" roll diameter rewind allows the operator to rewind multiple rolls from a single web simultaneously after slitting. It includes a 3" air core and a separate second Rewind Control Panel located at the Master Control Panel.
|-- 6 ft or 9 ft long top stacker for stacking printed sheets of irregular shapes in top-to-bottom order. It includes all appropriate mounting brackets, air bar, acceleration section to separate sheets, drive pulley, belt tightener, guard, support bar and Top Stacker Control Panel which includes the air bars “ON/OFF” switch, air pressure gauge and regulator knob, and the conveyor speed knob. The top stacker can be purchased with a batch counter that can speed up the conveyor belt momentarily at a pre-selected count for batch separation.
|-- Dual gearing allows the operator to run more than one gear series on the same press. The press can be configured with both1/8 CP gears on the gear side of the press and 32 DP gears on the operator side of the press.
|-- B-Bunch 590 Series Fan Folder for folding the finished product to be shipped in boxes. This unit includes the fan folder adapter kit and fan folder drive.
|-- T & P drop in type male/female punch unit punches holes in the material that will later be used in tractor feed type equipment. This unit fits in either die slot.
-- I Kela drop in type hot foil stamp equipment applies gold or foil stamp to the web while the press is running. This unit fits in either die slot.
|-- Variable information system for printing varying information or graphics while the press is running.
|-- Corona Treaters with support rolls, ozone destruct, auto power density and installation kit. This option allows the operator to treat the film surface for better ink adhesion.
|-- Web Cleaners, available in single or double side. This option cleans the surface of the web and picks up any contaminants prior to printing.
|-- Static Eliminators that help reduce any problems related to static. Helpful in maintaining the web clean and most advantageous in film applications.
|-- Delam/Relam Unit. This option is used with pressure sensitive material where the operator is required to separate the face stock from the paper support liner, print reverse on the backside (adhesive) and then relaminate the two substrates for final finishing.
|-- Safety cages installed to surround and guard the die cutting and printing stations.
-- Rotary Screen Printing can be easily integrated for value added printing.
|Die Cutting Package
|Typical Web Path
Allied Gear and Machine Company
St. Louis, Missouri
Contact us @